SPI Mold Finish – Practical Approach

Mold Finish – SPI Standard and the practical approach

SPI is the short form of the Society of Plastic Industry, who establish standards for plastic industry and the SPI Plastic Engineering Handbooks is one of the most important reference for engineers.

SPI defines the polishing standard on mold finish and widely applied in US markets. It helps to avoid grey areas and measure the finest of surface in the unit of Rough Average (Ra).

Nowadays, China’s standard is very much in line with SPI. However, there is little help using Ra value in China mold making industry because there is little chance to have precise equipment at site to do the precision measurement. What we needed is a practical guideline to more or less achieve the desired mold finish. Below guideline is widely accepted.

GLOSSY SURFACE, DIAMOND BUFF POLISH

SPI Finish A-1 — Grade #3, 6000 Grit Diamond Buff

SPI Finish A-2 — Grade #6, 3000 Grit Diamond Buff

SPI Finish A-3 — Grade #15, 1200 Grit Diamond Buff

NON-GLOSSY SURFACE, PAPER POLISH

SPI Finish B-1 — 600 Grit Paper

SPI Finish B-2 — 400 Grit Paper

SPI Finish B-3 — 320 Grit Paper

ROUGH SURFACE, STONE POLISH

SPI Finish C-1 — 600 Grit Stone

SPI Finish C-2 — 400 Grit Stone

SPI Finish C-3 — 320 Grit Stone

VERY ROUGH SURFACE, DRY BLASH POLISH

SPI Finish D-1 — 600 Stone Prior to Dry Blast Glass Bead #11

SPI Finish D-2 — 400 Stone Prior to Dry Blast #240 Oxide

SPI Finish D-3 — 320 Stone Prior to Dry Blast #24 Oxide

However, the above guideline falls short because it does not mention what steel should be used. For coarse surface, it may be fine. For demanding high glossy mold finish, the mold steel can be critical and the high glossy cannot be achieved without proper steel.  

For molding process, a melt plastic resin will be injected into a steel mold at high pressure and the steel will always face the issue of wear off. To produce a glossy product, the mold has to be significantly hard so that the shiny smooth surface will not be deteriorated quickly and the glossy surface can be remained for a longer period of time. The finer the surface is needed, the harder and the finer the steel is required.

Below is a supplementary guideline regarding steel to be used.

SPI Finish A1 – S136 Hardness at 54HRC

(Generally called “Super High Glossy” in China)

SPI Finish A2 – 718HH or NAK80 Hardness at 40HRC

(Generally called “High Glossy” in China)

SPI Finish A3 – 718H or S136 Hardness 32HRC

(Generally called “Normal Glossy” in China)

It is true that the steel made in China are somehow less consistent than from overseas. Therefore, it is suggested to use imported steel for demanding quality mold or at least use higher grade of steel from China to provide some buffer for the desired mold finish that you need.

Lastly, a high glossy mold finish is not equivalent to a high glossy finished product. It is significantly subject to other factors such as plastic resin used, molding condition and mold design. For example, ABS will provide higher glossy than PP, high temperature molding condition and non-flat surface will help to provide a much glossy finished product.

341 Responses

  1. Debbra says:

    Thanks for finally writing about > SPI Mold Finish
    – Practical Approach | Pro-A Innovation
    Limited < Liked it!

  2. Elizabeth says:

    Hey There. I found your blog using msn. This is a very well written article.
    I will be sure to bookmark it and come back to
    read more of your useful information. Thanks for the post.

    I’ll definitely comeback.

  3. Anderson says:

    Excellent article, I’ve learned a lot from this.

  4. Mohammad Sookoo says:

    I will right away grab your rss as I can’t find your e-mail subscription link or newsletter service. Do you’ve any? Please permit me know so that I may just subscribe. Thanks.

  5. Benito Soldner says:

    I gotta bookmark this net internet site it seems quite helpful incredibly useful

  6. Ellinore Perez says:

    Hi my loved one! I want to say that this post is amazing, great written and come with almost all important infos. I’d like to look extra posts like this .

  7. Plasma Cutting says:

    Heya i’m for the primary time here. I came across this board and I in finding It truly useful & it helped me out a lot. I hope to present something again and aid others like you helped me.

  8. Luella Austad says:

    Excellent post. I am dealing with some of these issues as well..

  9. John Wang says:

    Hi, we are getting quotes from Chinese tool makers. However, very few knew what SPI D1 is. Most of them only use: glossy and matte. I feel more comfortable to have sample chips of China National Stanadard (GB) and find the equivalent myself and order per local standards.

    • Simon Yeung says:

      There are still many Chinese tool makers don’t understand/follow GB standard. My article is intended to provide a helpful guideline to those who would like to achieve SPI finishing. Please note that workmanship is also critical to achieve the required finishing.

  10. Elise says:

    very nice publish, i actually love this website, keep on it

Leave a Reply

Your email address will not be published. Required fields are marked *